MAXFIT7F16DAPQ Altronix Access Power Controller Kit - BC300 Enclosure Indoor 13” W x 13.5” H x 3.25” D

Specifications

eFlow104N Series

Input

• Voltage - 120VAC, 60Hz, 4.5A max
• Fusing - 6.3A/250V

Output

• Voltage - 24VDC
• Current - 10A continuous max
• Protection - Fused 2.5A / PTC 2A
• Auxiliary - Class 2 power-limited @ 1A (unswitched)
• Other - Overvoltage protection. Filtered and regulated

Back-up Battery (not included)

• Capacity - 7AH / 12VDC (2 within enclosure), 12AH / 12VDC (requires larger “X” enclosure), 40AH, 65AH (requires separate enclosure)
• Type - Sealed lead acid or gel type
• Fuse Rating - 15A / 32VDC
• Failover - Upon AC loss, instantaneous

Fire Alarm Disconnect

• Supervised - Latching or non-latching
• EOL - 10K Resistor

Supervision

• AC Failure - Form “C” contacts
• Battery - Form “C” contacts
• Low DC Power Shutdown - Shuts down DC output terminals if battery voltage drops below 71-73% for 12V units and 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge

Indicators (LED)

• Input - 120VAC is present
• DC Output - Powered

Agency Listings

UL

• UL294 - Access Control System Units
• UL603 - Power Supplies for Use with Burglar-Alarms Systems
• UL1481 - Power Supplies for Fire Protective Signaling Systems

cUL

• ULC-S318-96 - Power Supplies for Burglar Alarm Systems. Also suitable for Access Control
• CSFM - California State Fire Marshall Approved
• CE - European Conformity

Physical and Environmental

• Dimensions (H x W x D) - 13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
• Product Weight - 6.8 lbs. (3.08 kg)
• Shipping Weight - 7.7 lbs. (3.49 kg)
• Operating Temperature - 0ºC to 49ºC (32ºF to 120ºF)
• Storage Temperature - -20ºC to 70ºC (-4ºF to 158ºF)
• Relative Humidity - 85% +/-5%
• BTU/Hr (approx.) - 123 BTU/Hr

LINQ8ACMCB Specifications

Input

• Two (2) Independent Low Voltage Inputs

Input Voltage Options

• Single Input - Input1: 12 or 24 VDC from eFlow series power supply
• Dual Input Option 1
  • Input 1: 12 or 24 VDC from eFlow series power supply
  • Input 2: 12 or 24 VDC from eFlow series power supply, 5 or 12 VDC from VR6 voltage regulator
• Dual Input Option 2 - 12 and 24 VDC from Tango1B PoE Driven Power Supply

Voltage Range

• 5VDC to 24VDC up to 10A each or 16A total input
• Current Consumption - 0.6A @ 12V, 0.3A @ 24V with all relays energized
• Main Fuse Rating - 15/32A

Outputs

• PTC protected outputs rated @ 2A per output, Class 2 power-limited. Total output 16A max
• Do not exceed the individual power supply ratings
• Any of the eight (8) fuse/PTC protected power outputs are selectable to follow power Input 1 or Input 2
• Individual outputs may be set to OFF position for servicing

Output Ratings

• PTCs are rated 2A each
• Total output current is determined by the power supply(ies), not to exceed a maximum of 10A for each input

Programming Features

Eight (8) Programmable Outputs

• Fail-safe, fail-secure or auxiliary outputs
• Input controlled or manually controlled through software
• High (over) and low (under) voltage and current monitoring by output
• Multiple outputs may be programmed to be triggered by a single input
• Battery back-up by output

Eight (8) Programmable Trigger Inputs

• Normally open (NO)
• Normally colsed (NC)
• Open collector sink inputs
• Wet Input (5VDC - 24VDC) with 10k resistor
• Any combination of the above

Other Programmable Trigger Inputs

• Monitor power supply(ies) input for voltage and currect limits (high/low)
• Input and output current calibration
• Programmable timer events
• Programmable user levels
• Enable or disable alerts by type
• Programmable alert reporting delay

Fire Alarm Disconnect

• Supervised - Inactive, latching or non-latching, individually selectable for any or all of the eight (8) outputs
• EOL - 10K Resistor

LED Indicators

• Green AC LED - Indicates AC trouble condition
• Green BAT LED - Indicates battery trouble condition
• Green FACP LED - Indicates FACP disconnect is triggered
• Flashing Blue Heartbeat LED - Indicates network connection
• Individual OUT1 - OUT8 Red LEDs - Indicate outputs are triggered
• Individual Voltage LEDs - Indicate 12VDC (Green) or 24VDC (Red)

Agency Listings

UL

• UL 294 7th Edition - Access Control System Units

Physical and Environmental

• Dimensions (W x L x H) - 8” x 4.5” x 1.25” (203.2mm x 114.3mm x 31.8mm)
• Product Weight - 0.7 lb. (0.32 kg)
• Shipping Weight - 0.95 lb. (0.43 kg)
• Operating Temperature - 0ºC to 49ºC (32ºF to 120ºF)
• Storage Temperature - -20ºC to 70ºC (-4ºF to 158ºF)
• Relative Humidity - 93% +/-5%
• BTU/Hr (approx.) - 4 BTU/Hr

PD16WCB Specifications

Input

• Voltage Range - 12VDC or 24VDC, up to 10A or 24VAC or 28VAC, up to 12A

Outputs

• Sixteen (16) PTC protected Class 2 Rated power-limited outputs (auto-resettable)
• 2A per output max
• Total output current should not exceed max current rating of power supply employed
• PTCs are rated @ 2A/250V

Indicators (LED)

• DC Output - Power LED

Agency Listings

UL

• UL294 - Access Control
• UL603 - Burglar Alarm
• UL1481 - Fire Alarm

cUL

• General Signaling Equipment Evaluated to CSA Standard C22.2 No.205-M1983
• Power Supplies for Burglar Alarm Systems ULC-5318-96

Physical and Environmental

• Dimensions (L x W x H) - 6” x 5.875” x 0.95” (152.4mm x 149.2mm x 24.1mm)
• Product Weight - 0.4 lbs. (0.18 kg)
• Shipping Weight - 0.5 lbs. (0.23 kg)
• Operating Temperature - 0ºC to 49ºC (32ºF to 120ºF)
• Storage Temperature - -20ºC to 70ºC (-4ºF to 158ºF)
• Relative Humidity - 85% +/-5%

EFLOW104N Specifications PDF

LINQ8ACMCB Specifications PDF

PD16WCB Specifications PDF