AL1024NKA8D Altronix 8 PTC 6Amp 24VDC or 6Amp 12VDC Access Control Power Supply in UL Listed NEMA 1 Indoor 12” W x 15.5” H x 4.5” D Steel Electrical Enclosure – Gray

Altronix AL1024NKA8D converts a 115VAC 60Hz input into eight (8) PTC protected outputs. Outputs are individually selectable, providing 12VDC or 5VDC up to 6A and/or 24VDC up to 10A (240W total power) for access control panels, door locks, and ancillary devices. Power outputs can be converted to dry form “C” contacts. Outputs are activated by an open collector sink, normally open (NO), normally closed (NC) dry trigger input, or wet output from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. AL1024NKA8D will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs. The spade connectors allow you to daisy chain power to multiple ACMS8 modules. This feature allows you to distribute the power over more outputs for larger systems.

Specifications

Power Supply (AL1024ULXB2)

Input

• Voltage - 115VAC 60Hz, 4.2A max
• Fusing - 5A/250V

Outputs

• Voltage - 24VDC
• Current - 10A @ 24VDC continuous max
• Other - Overvoltage protection, Filtered and regulated

Back-up Battery

• Capacity - 12AH /12VDC (2 within enclosure), 40 AH / 65 AH (requires separate enclosure)
• Type - Sealed lead acid or gel type
• Failover - Upon AC loss, instantaneous

Supervision

• AC Failure - Form “C” contacts
• Battery - Form “C” contacts

Indicators (LED)

• Input - 115VAC is present
• DC Output - Powered
• Battery - Discharged or not connected

Dual Input Access Power Controller (ACMS8CB)

Input

• Voltage - 24VDC from AL1024ULXB2 and 12VDC or 5VDC from VR6
• Input PTCs - 9A

Outputs

• Voltage - 12 or 24VDC individually selectable
• Eight (8) selectable 12VDC or 24VDC independently controlled outputs or eight (8) indepently controlled Form “C” relay outputs
  • a) Fail-Safe and/or Fail-Secure power outputs
  • b) Form “C” Relays. 28VAC or VDC @ 2.5A Rated
  • c) Auxiliary power outputs (unswitched)
  • d) Any combination of the above
  • Any of the eight (8) PTC protected power outputs are selectable to follow power Input 1 or Input 2
  • Individual outputs may be set to OFF position for servicing
• Output PTCs - 2.5A

Indicators (LED)

• Red LEDs - Outputs are triggered (relays energized)
• Blue LED - FACP disconnect is triggered
• Out1 - Out8 - Bi-colored LEDs indicate 12 or 24VDC

Voltage Regulator (VR6)

Input

• Voltage - 24VDC from AL1024ULXB2

Output

• Voltage - 12VDC
• Current - 6A continuous
• Other - Surge suppression

Indicators (LED)

• Input - 24VDC is present
• Output - Powered

Agency Listings

• CE - European Conformity
• All components of this kit are UL Listed sub-assemblies
• Please refer to the corresponding Sub-Assembly Installation Guides for further information

Physical and Environmental

• Dimensions (H x W x D) - 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm). Enclosure accommodates up to two (2) 12AH/12VDC batteries
• Product Weight - 9.4 lb. (4.26 kg)
• Shipping Weight - 10.5 lb. (4.76 kg)
• Operating Temperature - 0ºC to 49ºC (32ºF to 120ºF)
• Storage Temperature - -20ºC to 70ºC (-4ºF to 158ºF)
• Relative Humidity - 85% +/-5%
• BTU/Hr. (approx.) - 123 BTU/Hr

AL1024NKA8D Specifications Sheet

AL1024NKA8D Installation Manual