IMP1110-1ERI Pelco 2.8-10mm 30FPS @ 1080p Outdoor IR Day/Night Dome IP Security Camera 24VAC/PoE

Specifications

Camera

• Imaging Device - 1 MPx 1/4-inch 1280 x 720 (0.9 MPx)
• Imager Type - CMOS
• Imager Readout- Progressive scan
• Electronic Shutter Range - 1/5 ~ 1/10,000 sec
• Dynamic Range -65 dB
• White Balance Range - 2,500° to 8,000°K
• Digital Noise Reduction - Yes (ON/OFF selectable)
• Signal to Noise Ratio - 50 dB
• Minimum Illumination - 1 MPx f/1.4 0.30 lux 0.02 lux 0.00 lux 0.00 lux
• Mechanical IR Cut Filter - Yes (AUTO/MANUAL selectable), with different set points on lux
• IR Illumination - Adaptive IR up to 15 m; auto ON in night mode, or OFF
• Lens - 2.8 to 10 mm or 3 to 9 mm remote zoom with DC iris
• Focus - Autofocus

Lens

• Lens Type - Built-in; varifocal
• Focal Length - f/1.2, 3 ~ 9 mm
• Focus- Autofocus, motorized
• Zoom - Remote
• Auto Iris Type -DC drive P-iris lens
• Maximum Field of View - 1 Wide 4:3 Diagnol 74° Horizontal 58° Vertical 41° Tele 4:3 Diagnol 23° Horizontal 19° Vertical 14° Wide 16:9 Diagnol 84° Horizontal 71° Vertical 37° Tele 16:9 Diagnol 26° Horizontal 22° Vertical 13°

Video

• Video Streams - Up to 2 simultaneous streams, plus service stream; the secondary stream is variable based on the setup of the primary stream
• Video Overlay - Camera name, time, date
• Frame Rates- 1 MPx 30 (full), 25, 20, 16.67, 15, 12.5, 10, 5, 1
• Video Encoding - H.264 high or main profiles; and MJPEG
• Bit Rate Control -Constant bit rate (CBR), constrained variable bit rate (CVBR) with target range
• Service Stream - 320 x 240 (0.1 MPx) or 320 x 180; 2 ips, MJPEG
• Window Blanking - 4 configurable windows

Audio

• Streaming - Dual-channel
• Input - Line in/terminal block
• Encoding - G.711 A-law/G.711 U-law

Electrical

• Network Port - RJ-45 connector for 100Base-TX
• Power Input - PoE (IEEE 802.3af), Class 3 24 VAC nominal, 18 to 32 VAC range
• Power Consumption - <10.50 W
• Local Storage - Up to 32 GB on Micro SDHC or SDXC card
• Alarm Input -1
• Alarm Output - 1; PhotoMOS relay (30 V, 1 A)
• Triggers - Unsupervised mode that detects switch closures (N.O. and N.C.)

Environmental

• Operating Temperature - –40° to 50°C (–40° to 122°F)*
• Storage Temperature - –40° to 60°C (–40° to 140°F)
• Operating Humidity - 15% to 85%, RH condensing
• Storage Humidity - 20% to 80% RH noncondensing
*Thermostatically controlled heating provides ramped heating control between the initial heater on at 15°C (59°F) and full heating mode at –40°C (–40°F).

General

• Construction - Die-cast aluminum; polycarbonate bubble
• Ingress Protection - IP66 per IEC 60529
• Backlight Compensation - Off / BLC
• Vandal Resistance - IK10 (20J impact) per IEC 62262
• Finish - Light gray, RAL 7047; satin texture
• Pan/Tilt Adjustment - Manual
• Pan - 355°
• Tilt - 75°
• Rotate - 360°
• Weight - 0.86 kg (1.90 lb)
• Shipping Weight - 1.07 kg (2.36 lb)

Network

• Supported Protocols - TCP/IP, UDP/IP (unicast, multicast IGMP), ICMP, IPv4, SNMP v2c/v3, HTTP, HTTPS, SSL, SSH, SMTP, FTP, RTSP, UPnP, DNS, NTP, RTP, RTCP, LDAP (client), QoS
• Users Unicast - 1 administrator, up to 4 viewers
• Multicast - Unlimited users H.264
• Security Access - Multiple user access levels with password protection

Integration

• Video Management - Digital Sentry 7.3 (or later); Endura 2.0 (or later); Third-party VMS through Pelco API 1.0 and ONVIF Profile S
• Mobile Application - Integrated to Pelco Mobile App
• Video Motion Detection - Simple motion detection and camera sabotage
• Local Storage - Capture 5- or 10-second video clips on camera sabotage, motion detection, or alarm input; record video continuously in the case of network outage with option to overwrite; access video through FTP protocol
• Camera Discovery and Firmware - Cameras discovered and firmware upgrade through Pelco Device Utility 2 version 2.2; cameras discovered and firmware upgrade through Endura Utilities
• Web Browser Support - Microsoft Internet Explorer 8.0 and later

IMP1110-1ERI Specifications PDF